Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. 10 Jan Thank you for choosing this Mitsubishi Inverter. This Instruction Manual ( basic) is intended for users who “just want to run the inverter”.
|Published (Last):||11 July 2007|
|PDF File Size:||3.94 Mb|
|ePub File Size:||17.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
Selection of operation mode and operation location Parameter Switching the operation mode External operation Switching from the PU Switching from the network Press Switch to the external operation mode from the the PU to mitsubishi e700 vfd manual Press network.
If protective functions of E.
Line voltage drop [V] – Use a larger diameter cable when the wiring distance is long or when it mitsubishi e700 vfd manual desired to decrease the voltage drop torque reduction in the low speed range.
When changing the parameter values frequently, set “1” The motor capacity should be equal to or one rank lower than the inverter capacity. Reset method of protective function Troubleshooting Reset method of protective function Eliminate the cause of the error before you reset the inverter.
Perform mitsubishi e700 vfd manual inverter reset and restart tuning.
MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.
Corrective action Setting “0” in Pr. Reduce the load inertia. The parameter number read previously appears. Page RS communication with the PU connector.
Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller
Connection of stand-alone option units Wiring 3. Page Do not change the Pr.
Otherwise, the motor will start mitsubushi after resetting, leading to potentially hazardous conditions. Made valid when the RT signal is 0—A on. In addition, negative logic can be set on when the inverter is normal, off when the fault oc- curs. When vfr breaker on the inverter primary side trips, check for the wiring fault short circuitdamage to internal parts of the inverter, etc. Vfx If the Pr. Press the MODE key for 2s to show the key lock mode. Schematic diagram of data exchange If a data error is detected and a retry must be made, mitsubishi e700 vfd manual retry operation with the user program.
When the RT signal is mitsubishi e700 vfd manual, the mannual second function is selected at the same time. Refer to page This could cause a fire. Minimum and maximum output frequency Output frequency [Hz] Clamped at the maximum frequency Pr. A program should be created so that transmission is disabled receiving state when the computer is not sending and reception is disabled sending state during sending to prevent the computer from receiving its own data.
Depending on the direction of the flowing current, one distinguishes between: General flowchart NOTES Always set the communication check time interval before starting operation to prevent haz- ardous conditions.
PU indication is lit. The parameter can be set when Mitsubishi e700 vfd manual. This should be fully noted. LF line feed are automatically set at the end of a data group on some bfd. Page Output current is assumed as 0A to perform integration processing. Note that the internal thermal in- tegrated value of the electronic thermal relay function and the number of retries are cleared erased by resetting the inverter.
Set “50”Hz w700 Pr. Page 71 – Connection of the power improving DC rea Table Of Contents 6. Page It is recommended to install a mitsubishi e700 vfd manual to monitor voltage for checking the power supply voltage to the inverter.
Enclosure design Installation Arrangement of multiple inverters When multiple inverters are placed in manuql mitsubishi e700 vfd manual enclosure, generally arrange them horizontally mitsubishi e700 vfd manual shown in the figure a. Meters and measuring methods Troubleshooting 7. For write, set the data as a control input instruction. Page Page – Perform frequency setting by analog volt Selection and protection of a motor Parameter NOTES Fault by electronic thermal relay function is reset by inverter power reset and reset signal input.
Bold frame indicates stop-on-contact control is valid. Causes and corrective actions Troubleshooting Causes and corrective actions Error Message A message regarding operational troubles is displayed.
Page Stall prevention operation during acceleration may increase the acceleration time. Stall prevention is activated due to a mitsubishi e700 vfd manual Setting 22 too large may result in frequent over- load. If the sum of the time between Pr. When the MRS signal turns on opensthe inverter shuts off the output. The Mitsubishi e700 vfd manual cannot be connected when source logic factory setting is selected.
Frequency setting by analog input terminal 2, 4 Parameter 6. Inverter Placement Mount the inverter on a wall as specified. If communication is broken due to signal cable breakage, computer fault etc. Potentiometer at 20ma Refer to section 6. Any equipment placed above the inverter should be heat resistant.