The bath viscosity is close to that of water with little or no organic solvents in the coating bath. Another characteristic of the Autophoretic® coating process is that. Autophoretic Coating Process is a waterborne process in which organic polymeric emulsion gets chemically deposited on the surface of a clean metal substrate. Has anyone ever used or know anything about the Autophoretic® Coating Process? Thomas Moffitt. Massachusett’s Office of. Technical Assistance, Boston, MA.
|Published (Last):||18 September 2009|
|PDF File Size:||3.72 Mb|
|ePub File Size:||12.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Please contact your local PPG office for that paper. In our region actually several plants are coating truck frames. Solids – Dry autophoreitc thickness. CED, which means “cathodic electrodeposition”, is a type of electrophoretic deposition wherein autophoretic coating process work is cathodic. Equipment for powder coating is also available from many companies.
Autophoretic® Coating Process
The chemical reaction continues in the second layer, which results in film deposition and increased film thickness instead of solids loss to dragout. Please help improve it or discuss these issues on the talk page.
Thanks for the insights on the advantages of autophoretic coating. autophoretic coating process
In hot dip coating, where Zn getting may be diffused into the lattice structure of the Fe and get attached simple substitution. It’s not procesx to autophoretoc a finishing problem or the hazards of an operation via these pages. This autophoretic coating process needs additional citations for verification. I know that these two processes are not the same. There are probably technical articles and book chapters about these technologies, I am not familiar offhand with the reference material that you seek.
But in case of electrocoating, the surface atom of the lattice may autophoretic coating process bond with foreign atoms.
You could start with Henkel for info on the autophoretic coating process, and with this site’s supporting advertiser Coatec India or PPG, or other suppliers for info on the CED process. Has anyone experience with this coating on galvanized zinc surface?
Technically, frame coating process is divided into pre cleaning which depends up on the surface condition, the ACC Coating, rinse then reaction rinse, and curing; the autophoretic coating process could be summarized as follows: We looked at it for replacing some heavy zinc plating on couplings and had to dismiss it because the parts are handled very roughly and will chip and rust.
This allows the coating dispersion to flow into and around autophoretic coating process most complex shapes.
In the USA the method used by most of the frame manufacturing companies is electrocoat. But now we have another process reported to offer percent advantages over competitive coatings and 0 percent disadvantages.
Initially, the deposition process is quite rapid, but slows down as the film increases in thickness. A coating is a covering that autophoretic coating process applied to the surface of an qutophoretic, usually referred to as the substrate. Autophoretic coating has sort of a spring-loaded chemistry that reacts with the metal, causing chemical changes in the coating materials in the tank that result in deposition of the coating onto the substrate.
Since this process involves a mild acid acting on autophoretic coating process base part, can it result in delayed cracking under stress from hydrogen damage on a quench and tempered part as with other processes i.
It is definitely autophoretic coating process deformable than the CED coatings I have tested. In other projects Wikimedia Commons.
Coatings may autophoretic coating process applied as liquidsgases or solids. Electrocoat or electrodeposition is of course a painting process which is offered by several coatings manufacturers including PPG.
These ions interact with the latex in solution causing coating deposition on the surface of the steel parts. It’s not possible to diagnose a finishing problem or the hazards of an operation via these pages.
Autophoretic Coating vs. E-Coating (CED)
All information presented autophoretic coating process for general reference and does not represent a professional opinion nor the policy of an author’s employer. Functional coatings may be applied to change the surface properties of the substrate, such as adhesionwettability autophoretic coating process, corrosion resistanceor wear resistance.
A further consideration for ‘non-all-over’ coatings is that control is needed as to where the coating is to be applied. The line would most likely only be able to procesx zinc substrates and not plain steel at autophoretic coating process same time. A tubular application is an excellent example of one of the advantages A-Coat has over an electrostatic coating process which has throwing power limits to coat the entire inside surface depending, of course, on the geometry.
Also finish is important, being an auto component.
Autophoretic Coating Process
Want to decide on the process. The continuous formation of coating provides a film with a high degree of surface protection and corrosion resistance. Coqting there autophoretic coating process near future to autophoretic process in India when most of the automobile giants are referencing only CED process?