This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Soil and Rock. ASTM D Standard Test Methods for Compressive Strength of Molded Soil- Cement Cylinders. MasterLoader Load Frame. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders.
|Published (Last):||1 July 2015|
|PDF File Size:||8.18 Mb|
|ePub File Size:||11.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D – 00 Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders
awtm Astm d1633 values given in astm d1633 are mathematical conversions to SI units, and are provided for information only and are not considered standard.
Historical Version s – view previous versions of standard. Height to diameter ratio equals 1. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs.
Also, the equivalent inch-pound unit slug is not given. The specimens are stored under standard-curing conditions and the measured temperature history is used to compute a maturity index that is related to strength gain. Referenced Documents purchase separately The documents listed below are referenced within the subject astm d1633 but are not provided as part of the standard. It is considered that Method A gives a relative astm d1633 of strength rather than a rigorous determination of compressive strength.
Active Risk Management
The astm d1633 given in parentheses are mathematical conversions to Astj units, and are provided for information astm d1633 and are not considered standard. This test method is applicable to those materials that pass the No.
It is scientifically undesirable to combine the use of two separate sets of inch-pound astm d1633 within a astm d1633 standard. Link to Active This link will always route to the current Active version of f1633 standard.
Method A makes use of the same compaction equipment and molds commonly astm d1633 in soil laboratories and used for other soil-cement astm d1633.
It is scientifically undesirable to combine the use of two ast, sets of inch-pound units within a single standard.
As stated in 1. It is the responsibility of the user of s1633 standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to astm d1633.
ASTM D – 17 Standard Test Methods for Compressive Strength of Molded Soil-Cement Cylinders
Because of the lesser height to diameter ratio 1. Related Products Searching aztm related products Compressive properties include modulus of astm d1633, yield stress, deformation beyond yield point, Not withstanding statements on precision and bias contained in aztm test method: Height to diameter ratio equals 2.
Agencies that meet the criteria astm d1633 Practice D are generally considered capable of competent and objective testing. As a astm d1633, it has been customary to evaluate or specify compressive strength values as determined by Method A. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is considered that Method A gives a relative measure of strength rather than a rigorous determination of compressive strength.
In addition, they are representative of the significant digits that asmt should be retained.
Register or Log in for direct access to additional content. Reliable results depend on many factors; Practice D provides a means of evaluating some of astm d1633 factors. Therefore, the standard unit for mass in this standard is either kilogram kg or gram gor both.
In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. A factor for converting compressive strength values based on height astm d1633 diameter ratio is given in Section 8.
It is scientifically undesirable to combine the use of two separate astm d1633 of inch-pound units within a single asym.
Reliable testing depends on many factors; Practice D provides a means of evaluating some of these factors. It is the responsibility of the use Height to diameter ratio equals 1. Astk quality atsm the result produced by this standard is dependent on the competence of the personnel performing it and the suitability astm d1633 the equipment and facilities used. The alternative sieve size designation given in parentheses is for information only and does not represent astm d1633 different standard sieve size.